Mechanical Safety, Tensile Strength and Torque Testing of Baby Bottles, Children's Drinking Equipment and Accessories
Baby bottles, training cups, drinking containers and related accessories designed for infants and young children are products directly associated with children's health and safety. In addition to the properties of the materials used in their manufacture, mechanical durability, connection integrity and performance under foreseeable conditions of use are essential considerations in product design.
The TS EN 14350 standard establishes comprehensive safety requirements and test methods for drinking equipment intended for infants and young children. It covers mechanical and physical properties, chemical safety, packaging, marking and information supplied with the product.
The mechanical tests specified in the standard are particularly important for evaluating the tear resistance of feeding teats and drinking accessories, the integrity of connecting components, the durability of valve mechanisms and the behaviour of certain components when subjected to mechanical forces.
Tensile and Compression Testing Machines and Torque Testers provide valuable measurement capabilities for examining the mechanical properties of these products and improving quality control throughout manufacturing processes.
Properly configured testing systems enable manufacturers to measure mechanical performance, identify potential design weaknesses and support the development of safer products through objective and reproducible test data.
What Is the TS EN 14350 Standard?
TS EN 14350 is a standard that specifies safety requirements and test methods for drinking equipment intended for children aged 0 to 48 months.
The European standard EN 14350:2020+A1:2023 is adopted in Türkiye under the designation TS EN 14350+A1.
The standard covers reusable feeding bottles, drinking containers, drinking accessories, certain single-use products supplied with drinking equipment, and feeding teats.
Its primary objective is to reduce potential health and safety risks associated with the normal and reasonably foreseeable use of drinking equipment.
Within this scope, the following product characteristics are evaluated:
Mechanical strength and structural integrity
Tear resistance of drinking accessories
Operational safety of valve mechanisms
Connection strength of feeding teats and other applicable components
Secure attachment of protective covers
Mechanical strength of handles and connecting elements
Length, flexibility and safety of protruding parts
Potential hazards associated with cords and loops
Risks arising from the separation of small parts
Chemical safety of materials and product information requirements
The standard is not limited to mechanical testing. Nevertheless, tensile and compression tests play a significant role in evaluating several important mechanical safety requirements.
Importance and Purpose of TS EN 14350 Testing
Drinking equipment intended for infants and young children may be exposed to pulling, compression, bending and mechanical forces applied in different directions during use.
For example, an infant pulling on a feeding teat, a child manipulating the valve mechanism of a drinking cup or a toddler holding a training cup by its handles can subject the product to different mechanical stresses.
These forces may cause connections to loosen, materials to tear or components to become detached, potentially creating safety hazards.
Mechanical tests performed within the scope of TS EN 14350 enable measurable assessments of these risks.
The principal objectives of testing are to examine the resistance of materials and connections to specified forces, evaluate the risk of component separation or breakage, and determine whether products satisfy the safety conditions established by the standard.
These tests also help manufacturers improve material selection, product design, connection geometry and manufacturing quality.
Scientific Principles of Mechanical Testing According to TS EN 14350
Mechanical strength testing is based on the application of controlled forces to a material or product component and the examination of its physical response under loading.
During tensile testing, a specimen is subjected to a force applied along a specified direction. Its behaviour under load, including elongation, separation, tearing or fracture, is evaluated.
In compression testing, force is applied in the opposite direction to investigate the behaviour of the product under compressive or bending loads, depending on the test configuration.
The purpose of testing is not necessarily to determine the force at which a component breaks. Certain tests require a product to withstand a specified force for a defined period while maintaining its structural integrity.
Consequently, force measurement accuracy, movement speed, loading direction, specimen fixation and loading duration are parameters that directly influence test results.
Testing systems used for TS EN 14350 applications must therefore be configured to meet the conditions defined in the relevant test method.
Tear Resistance Testing According to TS EN 14350
Tear Resistance of Drinking Accessories
Clause 7.7.1 of the standard addresses the test method for evaluating the tear resistance of drinking accessories.
Feeding teats and applicable drinking accessories may experience mechanical stress caused by children's teeth and oral movements.
Components manufactured from elastic materials such as silicone and rubber must demonstrate adequate resistance to tearing or fragmentation under specified mechanical conditions.
The test method defined in the standard involves applying a controlled force to suitable drinking accessories using a specially designed penetrating probe and, where required, subsequently performing a tensile test.
A nominal force of 200 N is applied during the penetration stage. If penetration occurs, a nominal tensile force of 90 N is applied to the relevant component to evaluate whether tearing or separation takes place.
Different specimen preparation conditions apply to straws, as specified in the standard.
A Tensile and Compression Testing Machine capable of applying controlled forces may be used for the relevant stages of these tests.
However, force capacity alone is insufficient to ensure compliance with the test method. Appropriate specimen gripping arrangements, the required penetrating probe and the loading conditions specified by the standard must also be provided.
The results are important for assessing the mechanical safety of drinking accessories and investigating the suitability of elastic materials used in their manufacture.
Mechanical Durability Testing of Valve Mechanisms
Safety of Push-Pull Valves
Clause 7.7.2 of TS EN 14350 addresses the mechanical safety of drinking valves incorporating push-pull mechanisms.
These valves are commonly used in children's drinking cups and sports-style drinking spouts.
Valve mechanisms must operate safely during opening and closing, while their components should not become detached under mechanical stress in a manner that creates hazardous small parts.
The relevant test method includes an assessment of repeated valve operation followed by an examination of tensile strength.
Push-pull valves are subjected to 1,000 opening and closing cycles. Tensile strength is subsequently evaluated using the same specimen.
A nominal tensile force of 90 N is applied during the tensile stage. An additional requirement concerning opening force applies to conventional push-pull mechanisms.
A Tensile and Compression Testing Machine equipped with suitable fixtures can provide the controlled force required for the tensile strength stage.
However, the repeated opening and closing cycles may require a separate cycling mechanism or an appropriately configured automated testing system capable of meeting the conditions specified by the standard.
These tests help assess valve design safety and identify potential weaknesses in connections resulting from repeated operation.
Tensile Strength Testing of Protective Covers
Protective covers used with feeding bottles and children's drinking equipment help protect drinking accessories from external contamination and damage.
Some covers are completely removable, while others remain permanently attached to the product.
Clause 7.8.3 of TS EN 14350 includes a tensile test for evaluating the attachment integrity of permanently attached protective covers.
During the test, the protective cover and associated components are secured using an appropriate fixture. A specified force is applied in the direction and under the conditions defined by the standard.
Any fracture, tearing or separation of components is evaluated.
Examining the integrity of protective cover attachments is particularly important for reducing the risk of children being exposed to detached components during product use.
Tensile testing machines equipped with suitable grips and holding fixtures can provide the mechanical loading capability required for this type of assessment.
Mechanical Strength of Handles and Connecting Components
Training cups designed to help children develop independent drinking skills are commonly manufactured with one or two handles.
These handles may experience pulling, carrying loads and forces applied from different directions during use.
Clause 7.9 of TS EN 14350 covers mechanical safety requirements for handles and clips.
During testing, a controlled tensile force is applied to the handle or connecting component to evaluate its structural integrity.
The objective is to determine whether the component exhibits hazardous behaviour, such as fracture or tearing, under the conditions specified in the standard.
In addition to the accurate application of tensile force, proper specimen fixation is essential to prevent unwanted movement or damage that could affect the test results.
A Tensile and Compression Testing Machine equipped with appropriate specimen holders can be used for these connection strength tests.
Flexibility and Attachment Integrity of Protruding Parts
Feeding teats and certain drinking accessories contain components that protrude beyond the body of the drinking container.
Excessive length, insufficient flexibility or insecure attachment of these components may create potential hazards for children.
Clause 7.11 of TS EN 14350 addresses requirements relating to the length, flexibility and attachment integrity of protruding parts.
Flexibility Testing
Clause 7.11.2 covers the assessment of the bending behaviour of applicable protruding components under a controlled force.
During the test, the product is appropriately secured, and a compressive force is applied to the relevant component in a specified direction.
The behaviour of the component under loading is evaluated to determine whether the applicable safety requirements are satisfied.
A Tensile and Compression Testing Machine equipped with a suitable loading plate, connection fixtures and measurement system can provide the force application capability required for these tests.
Attachment Integrity of Feeding Teats
Clause 7.11.3 specifies a test method for evaluating the attachment integrity of applicable feeding teats.
The primary purpose of this test is to examine whether the feeding teat may tear, fracture or become detached from the container when subjected to defined mechanical loading conditions.
During testing, the product is assembled in accordance with the prescribed configuration. A tensile force is applied to the teat in the specified direction and at a controlled speed.
A nominal tensile force of 60 N is used in the relevant test method.
The specimen must be secured using an appropriate fixture, and the force must be applied at the correct angle to obtain reliable results.
This test represents an important mechanical safety application for which a Tensile and Compression Testing Machine may be used when equipped with fixtures suitable for the standard.
Safety Testing of Cords and Loops Under Tensile Force
Clause 7.12 of TS EN 14350 addresses safety requirements relating to cords and loops that may be incorporated into drinking equipment.
The evaluation considers potential entanglement and strangulation hazards associated with these components.
The standard includes methods for assessing cords and loops under specified forces.
During testing, a controlled tensile force is applied to the cord or loop, followed by the relevant length and circumference measurements. The integrity of loops is additionally evaluated under a higher force.
Tensile testing machines equipped with appropriate fixtures can assist in applying the controlled forces required for these tests.
However, completing the assessment in accordance with the standard also requires the relevant length and circumference measurements to be performed using the specified methods.
Importance of Torque Measurement in TS EN 14350 Applications
Many feeding bottles and children's drinking containers incorporate threaded caps, retaining rings and connecting components.
Correct assembly of these connections is important for product safety during use.
Insufficient tightening torque may result in inadequate connection security. Excessive torque, on the other hand, may introduce unwanted mechanical stresses into connecting components.
For this reason, evaluating the torque characteristics of threaded connections can provide valuable information during manufacturing and quality control.
Difference Between Tightening Torque and Opening Torque
Tightening torque is the rotational moment applied when assembling a threaded connection.
Opening torque, also referred to as removal torque, is the rotational moment measured when loosening or opening an assembled connection.
These values are not necessarily identical.
Connection geometry, surface friction, material properties and assembly conditions can influence the opening torque.
In the feeding teat attachment integrity test specified in Clause 7.11.3 of TS EN 14350, applicable specimens incorporating retaining rings must be prepared using a defined assembly torque.
The relevant test method specifies an assembly torque of 1.75 ± 0.25 Nm.
This requirement concerns the preparation of the specimen under prescribed conditions before the tensile test.
A Torque Tester can be used to measure the opening torque of a product and evaluate the torque characteristics of threaded connections.
However, measuring opening torque does not, by itself, verify that the assembly torque specified by the standard has been applied.
Appropriate torque application or control equipment is required to set and verify assembly torque.
Nevertheless, opening torque measurements are valuable for evaluating connection performance and supporting quality control in the manufacture of feeding bottles and caps.
Torque Tester
A Torque Tester is an electronic testing instrument designed to measure the rotational moment associated with mechanical connections.
It is particularly suitable for determining the opening torque of threaded caps.
The instrument automatically rotates the specimen and measures the torque generated during cap opening.
Its electronic measurement system enables torque values to be displayed digitally, while the maximum measured torque can be stored in memory.
Technical Specifications
Electronic measurement system: Provides electronic measurement of the rotational moment applied to the specimen.
Digital display: Allows the operator to monitor measured torque values.
Automatic rotation mechanism: Enables opening torque measurements through automatic specimen rotation.
Maximum torque recording: Stores the highest torque value reached during testing.
Different capacity options: Offers measurement capacity options for various products and applications.
Power supply: 220 VAC, 50 Hz.
Manufacturing and Quality Control Advantages
Torque measurement is an important quality control method for manufacturers of feeding bottles, caps and related threaded components.
These measurements allow manufacturers to examine variations in opening torque between production batches, investigate the consistency of assembly processes and compare the mechanical performance of different connection designs.
The instrument's automatic measurement system and maximum torque recording function facilitate the monitoring of measurement data during quality control activities.
Tensile and Compression Testing Machine
A Tensile and Compression Testing Machine is designed to evaluate the mechanical behaviour of materials and product components under controlled loading conditions.
With a force capacity of up to 3 kN, the machine can be used for various tensile, compression, rupture, tearing and connection strength tests.
For applicable mechanical tests under TS EN 14350, its force measurement capabilities, precise movement system and optional specimen grips can provide a suitable testing platform.
Technical Specifications
Force capacity: Offers capacity options for tensile and compression testing up to 3 kN.
Measurement accuracy: Provides precise force measurement capability with a stated accuracy of ±0.5%.
Movement resolution: A specified movement resolution of 0.001 mm supports controlled specimen displacement.
Adjustable test speed: Allows movement speed to be adjusted according to the requirements of the test.
Force units: Supports measurement in different force units, including newtons, kilonewtons, kilogram-force and gram-force.
Touchscreen control panel: Facilitates test parameter management and monitoring of measurement information.
Test termination functions: Provides stopping options based on specimen rupture, fracture or predetermined displacement.
Optional special grips: Allows the use of fixtures and grips suitable for different specimen geometries and test methods.
Optional software and connectivity: Additional options may support test data evaluation and reporting.
Advantages for TS EN 14350 Testing
The machine's controlled force application capability provides an important testing platform for applicable mechanical tests specified in the standard.
When equipped with suitable test fixtures, it can be used for tear resistance, valve attachment strength, handle integrity, feeding teat attachment security and other relevant tensile tests.
However, the suitability of the machine for a particular standardized test must be evaluated not only in terms of maximum force capacity but also with regard to load cell measurement range, accuracy, movement speed and specimen gripping arrangements.
Where a test method requires specialized apparatus or additional testing procedures, these must also be provided.
Specimen Preparation and Testing Conditions for TS EN 14350
Proper specimen preparation and controlled testing conditions are essential for obtaining reliable mechanical test results.
TS EN 14350 specifies preparation and conditioning procedures that must be considered before mechanical testing.
Depending on the product and the applicable test method, these procedures may involve pre-treatment, boiling-water treatment and conditioning under controlled environmental conditions.
These processes are intended to ensure that the mechanical behaviour of products is evaluated under defined and comparable conditions.
Correct specimen positioning is equally important during testing.
In tensile tests involving feeding teats and flexible drinking accessories, the grips must be configured to avoid introducing unintended damage that could influence the test result.
Similarly, the direction of force application, movement speed and loading duration must comply with the relevant test method.
Proper specimen preparation and testing conditions improve the comparability, reliability and repeatability of measurement results.
Advantages of TS EN 14350 Testing Equipment for Manufacturers
Improved Product Safety
Mechanical strength testing helps manufacturers assess specific safety risks that products may encounter during use.
In particular, examining the tearing of drinking accessories, separation of connecting components and detachment of parts supports the development of safer product designs.
Manufacturing Quality Control
Tensile strength and torque measurements provide quantifiable information about the materials and connection systems used in production.
Manufacturers can use this information to compare production batches and improve quality control procedures.
Product Design Optimization
Test results can help identify potential weaknesses in product design.
For example, insufficient mechanical strength in feeding teat attachments may indicate a need to reconsider material selection or connection geometry.
Similarly, variations in the torque characteristics of threaded caps may indicate the need to investigate manufacturing and assembly processes.
Support for Laboratory Testing
Testing machines capable of applying controlled forces enable a variety of mechanical assessments to be performed in product development and quality control laboratories.
Systems equipped with specialized grips and connection fixtures can be adapted to different product geometries and testing requirements.
Contribution to Export and Conformity Assessment
Meeting applicable safety requirements is essential for manufacturers intending to market infant and children's products internationally.
Mechanical tests performed within the scope of TS EN 14350 contribute to the technical evidence used in product safety assessments.
However, determining conformity with the standard requires all applicable requirements within the product's scope to be evaluated.
Performing tensile or torque measurements alone does not demonstrate conformity with the complete TS EN 14350 standard.
Applications of TS EN 14350 Testing Equipment
Feeding Bottle Manufacturers
Feeding bottle manufacturers can use mechanical testing systems to evaluate feeding teat attachment integrity, the mechanical properties of caps and the tensile strength of applicable components.
Feeding Teat and Drinking Accessory Manufacturers
The tear resistance and mechanical durability of drinking accessories manufactured from silicone, rubber and other suitable materials are important factors in product safety assessment.
Training Cup Manufacturers
Handles, valves and other connecting components incorporated into children's training cups can be evaluated for mechanical safety.
Cap and Plastic Connection Manufacturers
Torque measurements of threaded caps and retaining rings help assess manufacturing quality and connection characteristics.
Testing and Quality Control Laboratories
Laboratories performing tests on infant and children's products can evaluate the mechanical strength of different components using appropriately configured testing systems.
Research and Product Development Centres
Research facilities developing new materials, alternative connection systems and innovative product designs can use mechanical testing results to assess product performance and support design improvements.
Selecting Testing Equipment for TS EN 14350 Applications
When selecting mechanical testing equipment for TS EN 14350 applications, the force capacity, movement speed, measurement accuracy and specimen connection requirements specified by the relevant test method must be considered.
Tensile and Compression Testing Machines provide the basic force application and measurement capabilities required for tear resistance, connection strength and other applicable mechanical loading tests.
Torque Testers complement these assessments by measuring the opening torque of threaded caps and supporting the evaluation of connection performance during quality control.
These two types of equipment measure different mechanical quantities.
A Tensile and Compression Testing Machine is used for tests involving linear forces and displacement, while a Torque Tester measures rotational moment.
Consequently, the instruments cannot be used interchangeably. Each must be selected according to the mechanical quantity and testing procedure involved.
Furthermore, not all mechanical and chemical tests specified by TS EN 14350 can be performed using these two machines alone.
Depending on the characteristics of the product, specialized testing fixtures, cycling mechanisms, measurement templates, chemical analysis instruments and other laboratory equipment may be required.
Appropriate equipment selection must therefore be based on a comparison between the technical specifications of the instrument and the requirements of the relevant clauses of the standard.
Conclusion
The TS EN 14350 standard plays an important role in evaluating the safety of feeding bottles, drinking containers and associated accessories intended for infants and young children.
Its mechanical testing requirements address essential characteristics such as tear resistance, connection integrity, valve durability and the mechanical strength of handles and protective covers.
A Tensile and Compression Testing Machine, when combined with appropriate testing fixtures, provides controlled force application and measurement capabilities for several mechanical strength tests covered by the standard.
A Torque Tester offers a complementary measurement solution, particularly for assessing the opening torque of feeding bottle caps and drinking container closures and monitoring connection quality.
The correct application of these instruments enables manufacturers to obtain meaningful mechanical performance data, improve product designs and strengthen manufacturing quality control procedures.
For products intended for infants and young children, reliable safety assessment depends on performing the applicable tests using appropriate equipment, under defined testing conditions and in accordance with the relevant requirements of the standard.
RELATED PRODUCTS
RELATED SUBJECTS
- Bandage Adhesion Strength Test and Tensile-Compressive Properties
- DIN EN ISO 10555 Tensile Test of Catheter Systems
- Glass Material Bending Test Device
- Izod Charpy Digital Impact Testing Machine
- Needle Flame Test Device: Fire Safety Testing According to EN 60695-22 Standard
- What Is a Residual Seal Force (RSF) Test Device and What Is RSF?
- What Is the Ozone Test and How Is It Performed?
- What is Elmendorf Tear Strength?
- What is a Rubber Abrasion Tester and What Is It Used For?
- What is the Sponge Fatigue Test?